Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Bathtub Surround
Blog Article
How do you feel in relation to Tools You Need to Install a New Bathtub ?
Mounting a bathtub isn't precisely rocket science, however it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough project. If the old tub is conveniently accessible, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and also position the new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Ensure you have actually certified yourself for the job as well as fit trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This article will assist you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water pipes.
Your tools and material checklist ought to make up the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited accessibility that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipelines have been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using both wooden boards under its feet, put the bathtub in the needed placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
Turn on the water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub as well as additionally check the overflow outlet as well as the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the bathtub should wait till the bathtub has been utilized a minimum of when as this will certainly resolve it into its final setting.
Preparing for the Installation
First of all, the supporting framework provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Ensure you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface in between the bath and the tiling, bring about issues with dampness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the bathtub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily readily available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that editorial on A Step-by-Step Guide to Installing a Bathtub through a friend on our other domain. Sharing is nice. One never knows, you may be doing someone a favor. Kudos for your time. Visit us again soon.
Set An Appointment
Report this page